Looking for:
K8n neo4 manual |
MSI K8N NEO4 F User Guide Manual Download
- K8n neo4 manual
Author: jhony-esteban-beron-munoz. Embed Size px x x x x These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency основываясь на этих данных and, manhal not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a k8n neo4 manual area is likely to cause harmful interference, in which case k8n neo4 manual user will be required to correct the interference at his own expense. Notice 1 The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.
Notice nanual K8n neo4 manual interface cables and Kk8n. Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation. W e take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents.
Our products are under continual improvement and we reserve the right to make changes without notice. TrademarksAll trademarks are the properties of their k8n neo4 manual owners. Intel and Pentium are registered trademarks of Intel Corporation. Microsoft is a registered trademark of Microsoft Corporation.
Netware is a registered trademark of Novell, Inc. Award is a manuaal trademark of Phoenix Technologies K8n neo4 manual. Revision HistoryRevision V1. Technical SupportIf a problem arises with your system and no solution can be obtained from the users manual, please contact your place of purchase or local distributor.
Alternatively, please try the following help resources for further guidance. Safety Instructions1. Always read the safety instructions carefully. Keep this Users Manual for future reference. Keep this equipment away from humidity. Lay this equipment on a reliable flat surface before nro4 it up.
The openings on the enclosure are for air convection hence protects the equipment from overheating. Do not cover the openings. Place the power cord such a way that people can not step on it. Do not place anything over the power cord. Always Unplug the Power Cord before inserting any add-on card or module. All cautions and warnings on mannual equipment should be noted. Never pour any liquid into the opening that could damage or cause electrical shock.
If any of the following situations arises, get the equipment checked by mankal service personnel: The power cord or plug is damaged. Liquid has penetrated manua k8n neo4 manual equipment. The equipment has been k8n neo4 manual to moisture. The equipment has not work well k8n neo4 manual you can not get it work according to Users Manual.
The equipment has dropped and damaged. The equipment /21251.txt obvious sign nro4 breakage. Do not leave this equipment in an environment unconditioned, storage temperature above 60 0 C 0Fit may damage the equipment.
Replac e only with the same or equivalent type recommended by the manufacturer. Getting Started Hardware Setup BIOS Setup Introduction to DigiCell Audio Speaker Setting Chap t er 1. X ATX mainboard. Support 3. As the end user cannot boot without SP4, a combination installation CD must be created before attempting to install the manuall system onto the bootable RAID volume.
Hardware K8n neo4 manual chapter tells you how to k8n neo4 manual the CPU, memory modules, and expansion cards, as well as how to setup the jumpers on the mainboard. Also, it provides the instructions on connecting the peripheral devices, such as the mouse, keyboard, etc. W hile doing the installation, be careful in holding the components and follow the installation procedures. W hen you are installing the CPU, make sure the CPU has a heat sink and a cooling fan k88n on the top to prevent overheating.
If you do not have the heat sink and cooling fan, contact your dealer to purchase and install them before turning on the computer. MSI Reminds You Overheating Overheating will seriously damage the CPU and system, always make sure the manuql fan can work beo4 to protect the CPU from overheating.
Overclocking This motherboard is designed to support overclocking. However, please make sure your components are pro tools 10 manual download to tolerate such abnormal setting, while doing overclocking. Any attempt to operate beyond manyal specifications is not recommended. We do not подробнее на этой странице the damages or risks caused by inadequate operation or beyond product specifications.
Please turn off the power andunplug the power cord before installing the CPU. Sliding Plate 90 degree. Pull the lever s ideways awayfrom the socket.
Make sure to raise the lever up k8j a degree angle. Gold arrow. Look for the gold arrow on the CPU. The gold arrow should nanual as shown in the picture. Lower the CPU down onto the socket. If the CPU is correctly installed, the pins should be completely embedded into the socket and can not be seen.
Please note that any violation of the correct in s tal lati on p roc edur es m ay cause permanent damages to your больше на странице. Press the CPU down firmly intothe socket and close the lever. As the CPU is likely to move while the lever is being closed, always close the lever with your fingers pressing tightly on top of the CPU to make sure the CPU is k8n neo4 manual and completely embedded into the socket.
Turn over the mainboard again, and plac e the mainboard on the f lat surface. Locate the two screw holes of the mainboard. Turn over the mainboard, and install the backplate to the proper position. Align the retention mechanism and the backplate. Fix the retention mechanism and the backplate with two screws. Position the cooling set onto the retention manuak.
Hook one end of the clip to hook first, and then press down the other end k8n neo4 manual the clip to fasten the cooling set on the top of janual retention mechanism.
While disconnecting the Safety Hook from the fixed bolt, k8n neo4 manual is necessary to keep an eye on your fingers, because once the Safety Hook is disconnected from the fixed bolt, the fixed lever will spring back instantly. It uses 2. Users can install either single- or double-sided modules to meet their own needs.
However, the same type and density memory modules are necessary while using dual-channel Mwnual, or instability may happen. Please refer to the following table for detailed manuql DDR. Other combination not listed below will function as single-channel DDR.
The maximum memory speed decreases when the following two Memory Combination is selected you can also refer to the Recommended Memory Combination list shown in the previous page: - Each channel is installed with two double-sided memory modules - Both DIMM1 and DIMM3 slots are installed with double-sided memory j8n. Installing DDR Modules1.
The module will only fit k8n neo4 manual the right orientation. Then push it in manial the golden manaul on the memory module is deeply inserted in the socket.
The plastic clip at each side of the DIMM slot will automatically close. You can barely see the golden finger if the k8n neo4 manual is properly inserted in the socket. Before inserting the power supply connector, always make sure that all components are installed properly to ensure that manial damage will be caused.
To connect the SSI power supply, make sure the plug of the power supply is pin 13 k8n neo4 manual in k8n neo4 manual proper orientation and k8n neo4 manual pins are aligned. Then push down the power supply firmly into the connector. These two connectors connect to the ATX power supply and 8kn to work together to ensure stable operation of the mainboard.
Power manuao of watts and above is highly страница for system stability. Important Notification about Power IssueNForce chipset is very k8n neo4 manual to ESD Electrostatic Dischargetherefore this issue mostly happens while the users intensively swap memory modules under S5 power-off states, and the power code is plugged while installing modules.
Due to several pins are very sensitive to ESD, so this kind of memory-replacement actions might cause system chipset unable to boot.
Please follow the following solution to avoid this kn. You can attach a serial mouse or other serial devices directly to the connector. You can plug the USB device lippincott manual of practice 9th edition free into the k8n neo4 manual.
Comments
Post a Comment